Kitchen - Glass SplashBack

Taking Measurements

On 25-April-08 two guys from L&K Aluminum & Glass Works PL came to take measurements for the glass splashback. The glass panel would be spray-painted black and cover the entire back wall of the kitchen cabinet in the photo below:

White tiled wall above burner hob will be covered with glass panel


They brought a special laser beam instrument to aid them in the measurements, probably as a visual aid to assess the exact vertical and horizontal axes for the glass panel.

Laser Beam Instrument






One Month Later - Installation

Today - Thu, 22-May-08 - the L&K guys came to install the glass splash back! Why did it take L&K almost a month after the initial measurement for the installation? Well, they made mistakes.

The guys came within one week after they first took measurements on 25-Apr, bearing 3 glass pieces for the back panel. That took me by surprise.

I had previously asked the ID to remind L&K that the glass splash back should be in one single panel. Any visible seam on the glass splash back would not be a pretty sight. So what were the guys doing with 3 cut glass pieces when they were supposed to bring only one?



I called the ID. The ID assured me the factory had made a mistake. He spoke to the guys, that was followed by some hurried phone calls between the guys and the factory. Finally, the guys acknowledged the mistake, apologized, and promptly took the panels back.

Two weeks later, an L&K guy came in the late afternoon. Asked why, he said the factory had misplaced the earlier measurements! He needed to retake those measurements for the glass splashback.

All those mistakes surely cost money. Would the additional costs be charged to us? We don't have the answer, yet. The final bill for the kitchen cabinets has not been tallied. The ID assured us he would tote up all the bills and add 10% for his fee.

Trust is not something we gave easily. It has to be earned. Once lost, trust is seldom regained.

As the ID had shown integrity in his dealings with us so far, we decided to trust him and await the final bill.

Silicone applied to tiled wall




Tempered Glass
When we saw silicon applied to the entire back wall, we asked the guys what would happen if we need to replace the glass. They said they could break and remove the glass panel without affecting the tiled back wall. They assured us the glass panel would not shatter or break from the radiant heat of the burner as they used tempered glass for the panel.

Tempered Glass



Preparing to lift the glass panel



Note how much the guy perspired during the installation process!


Finishing with silicone sealant around glass edges



"Less-than-perfect" fit of the glass panel is more apparent than real..


We viewed the completed splashback with mixed feelings.

First, the "less-than-perfect" fit of the glass panel where it meets the wall cabinet is a limitation inherent with the installation process. The glass guys had told us before they went ahead to measure and cut the glass that there would be a small line gap where the glass panel meets the top kitchen cabinets to facilitate installation. The gap space is intentional and serves to avoid scratching the base of the white cabinet as the panel is carefully and slowly "pushed" onto the back wall during the actual installation process. It was an inherent aspect of the job, and won't look too obvious or bad either. A similar 2mm allowance was made for the vertical side of the panel. We accepted the explanation.

Second, we thought the original white tiled wall looked pretty good. Maybe we should have gone for a white colored back splash instead? But then, we decided the black splash back looks quite chic and classy. So there - you decide!

Finally, would cleaning up oily residue on the back wall after cooking be easier henceforth? Perhaps it would be, we mused.

But was the extra cost worth it?

5 comments:

Anonymous said...

Hi, how much you spend just for the backsplash?
cos my new house also have tiles.. and i want to put backsplash just like yours.
please email me the detail.. thank you
ssideqa@yahoo.com

thank you in advance
from siddeeqa

glass splashbacks said...

That comes pretty neat. I am actually looking for a smooth and glossy splash backs. Love the black one. I think that would be perfect in my kitchen.

GreenCoal said...

Yes, we think so. Although I wouldn't mind a creamy white spray-painted splash back.

Thanks for your comment.

GreenCoal said...

Hi siddeeqa,

I think my response is on the Blog to help other readers too. Thanks for asking.

Anonymous said...

Hi, thanks for sharing. Can you pm me the contact and quotation. The backing temper look great.

Lcnem80@hotmail.com
Thanks

Post a Comment

Hi, thanks for your comments. While I will strive to answer all your queries please be patient as I am overwhelmed at work.

Thanks for your understanding,

GreenCoal

 

Copyright © 2008-2011 bfcAsia - All photos and contents are copyrighted material of shunFoto.com • All Rights Reserved